There are many reasons why you might want to move a toilet a few inches, including: making room for a new bathroom fixture, improving the bathroom layout, or getting access to a difficult-to-reach area. Whatever the reason, it is possible to move a toilet a few inches without professional help.
Yes, most toilets can be moved a few inches if necessary. However, it is best to consult a professional before moving a toilet to ensure that it is done correctly.
Table of Contents
Is it difficult to move a toilet over a few inches?
If you need to move your toilet more than just a couple of inches, you will need to demolish the concrete to access and relocate water and waste lines. Then you will need to rebuild the concrete foundation and replace the sub-flooring, flooring, and fixtures.
The cost to move a toilet or sinks can be $2,500-$3,500 per fixture. Plumbing can be a significant cost factor in a remodel when a bathroom floor plan is altered.
How many inches can you move a toilet with an offset flange
If you need a little extra distance from your existing toilet sewage pipe, head to your local home improvement store and pick up a toilet offset flange. This handy device works with both 3-inch and 4-inch sewage pipes, and can give you up to 2 inches of extra space in any direction.
If you’re planning on moving your toilet, there are a few things you’ll need to do to make sure the process goes smoothly. Here are 8 simple steps to follow:
1. Make a plan
Before you start moving anything, it’s important to have a plan in place. Decide where you want the toilet to be moved to and make sure there’s enough space for it.
2. Make space for the toilet
Clear out any obstacles in the way of where you want the toilet to be moved. This will make it easier to move and avoid any damage.
3. Turn off the water
To avoid any accidents, make sure to turn off the water supply to the toilet before you start moving it.
4. Remove remaining water
There will likely be some water left in the toilet bowl and tank. Use a sponge or towel to remove as much water as possible.
5. Disconnect the supply line from the toilet
There will be a water supply line connected to the toilet. Use a wrench to loosen the connection and disconnect the line.
6. Remove the bolts
There will be bolts holding the toilet to the floor. Use a wrench to remove these bolts
Can I move my toilet 6 inches?
If you need to move your toilet, you can use an offset toilet flange. This will allow you to move the toilet by a few inches on any side, without having to make a new hole in the floor. This can be a great way to save money, as you can reuse the same wastewater line.
If you’re planning on moving your toilet, it’s best to involve a professional. Your plumber will need to move the drainage and water supply to accommodate the new location. This is not a straightforward weekend DIY job, but it is doable with the help of a professional.
Why is it expensive to move a toilet?
If you’re thinking about changing the layout of your bathroom, be aware that it could significantly increase the cost of your project. Plumbing is a complex system, and even small changes can have a big impact on the overall cost. In some cases, you may be able to save money by doing the work yourself, but in most cases, it’s best to leave it to the professionals.
If you are considering re-fitting your kitchen, you will not need planning permission unless your building is listed. However, you may need to apply for building regulations approval if you are adding a new bathroom.
How much does it cost to have a toilet swapped out
The cost of replacing a one-piece toilet can range from $200 for the toilet and labor, to as much as $850 depending on the cost of the toilet and the amount of labor needed to install it. Two-piece toilets can cost between $300 for installation and the toilet, to as much as $1,000.
If you are installing a new toilet, be sure to install the flange at the correct height. A best practice is to install the flange on top of the finished floor. This will ensure that there are no leak paths.
What is code for distance around a toilet?
Most codes require at least 15 inches (measured from the center of the toilet) from any side wall or obstruction and not closer than 30 inches center to center to any other sanitary fixture. The NKBA actually recommends 32 inches.
A 10-inch rough-in is less common than a 12-inch rough-in, but it is still a useful size to know about. Toilets that come in a 10-inch rough-in can be used in smaller bathrooms or as a space-saving option in larger bathrooms.
Is it a big deal to move a toilet location
The most difficult part of moving a toilet is actually relocating the drainage and water supply plumbing to the new location. This can be a time-consuming and difficult process, depending on the layout of your home and the location of the new toilet. However, once the plumbing is in place, installing the toilet is a relatively easy task that should take less than an hour.
The toilet flange must be at least 15 inches away from any sidewall or nearby fixture. However, 15 inches is the absolute minimum. A 15-inch distance from the vanity, shower, tub and back and side walls are required to accommodate the toilet flange.
How far away from the back wall should a toilet be?
The standard distance from the back wall for a toilet flange is 12 inches, or 12-1/2 inches from the center of the flange to the wall framing. This means that the plumber should set the toilet flange at least 15-1/2 inches from the center of the flange to the wall framing.
It is possible to move a toilet even if it has been installed on a concrete slab. This is because the slab can be cut and broken apart to allow the toilet to be removed and then replaced in a different location.
Final Words
To move a toilet a few inches, you will need to remove the complete unit from the floor flange. You will then need to reinstall it in the new location, making sure to properly secure it to the floor flange.
If you need to move a toilet a few inches, you can do so by disconnecting the flange from the floor, moving the toilet, and then reconnecting the flange. You may need to adjust the water supply line and the waste line accordingly.