In order to measure toilet rough in size, you will need a tape measure. Start by measuring the distance from the back wall to the center of the drain. Then, measure the distance from the side wall to the center of the drain. The rough in size is the average of these two measurements.
There are a few different ways that you can measure toilet rough in size. One way is to measure from the back wall of the toilet to the center of the drain. Another way is to measure from the center of the drain to the center of the bowel opening.
Table of Contents
How do I know if my toilet is 10 or 12 rough-in?
If you’re replacing an old toilet, you’ll need to know the rough-in size. The rough-in is the distance from the center of the drainpipe to the wall. To measure, start at the center of the bolts that hold the toilet to the floor. Measure to the wall, not the baseboard. There should be 24 inches of clearance from the wall facing the bowl and 15 inches on each side. If your measurements are between 115 and 125 inches, it is a 12-inch rough-in.
It is possible to install a toilet designed for a 10-inch rough-in into a space that has a 12-inch rough-in. However, this may not be the ideal situation. If possible, it is best to match the rough-in for your bathroom plumbing to the rough-in for the toilet.
How much space is behind a 12 in rough-in toilet
The rough-in for a toilet is the distance from the center of the flange to the finished back wall. 12 inches is the most common rough-in size for toilets. This information can be found on the toilet’s specification sheet.
When measuring a toilet’s rough-in distance, it is important to take into account the baseboard and not to measure from it. This will ensure an accurate measurement and avoid buying the wrong fixture for your bathroom.
Are most toilets 10 or 12 rough in?
A standard toilet rough-in is 12 inches, but some older homes come with 10” or 14” rough-in sizes. You may also find 10” rough-in sizes in powder rooms, half baths, or other small bathrooms to save space.
Most codes require at least 15 inches (measured from the center of the toilet) from any side wall or obstruction and not closer than 30 inches center to center to any other sanitary fixture (The NKBA actually recommends 32 inches). There should be at least 24 inches of clear space in front of a toilet or bidet.
What is the most common toilet rough-in size?
The standard rough-in for a toilet is 12 inches, but you may encounter 10-inch and 14-inch rough-ins in older homes. You should be able to find the rough-in measurement in the new toilet’s product information. Once you know the rough-in, you can determine whether you need a 10-inch, 12-inch, or 14-inch toilet.
There are elongated toilets built to fit a 10” rough-in, and some are built to fit 14”. If you have a 10” rough-in, you will need to purchase a toilet that is built to fit that size. If you have a 14” rough-in, you can purchase either size toilet.
Why would I want an elongated toilet bowl
Elongated bowls are also considered more ‘hygienic’ in that the larger surface area of the bowl makes is easier for men and children to use with less mess. The longer bowl size is also a requirement for ADA use, and the longer/wider bowl is generally easier to use for those with mobility issues.
When choosing a toilet, one of the key measurements to consider is the rough-in. This is the distance from the wall to the center of the drainpipe. Most toilets have a 12-inch rough-in, but you may also find toilets with a 10- or 14-inch rough-in. Toilets with a smaller rough-in may be a little less common, so you may have less of a selection to choose from. Keep this measurement in mind when shopping for a toilet to ensure you find one that will fit in your space.
How many inches above a toilet should you hang a picture?
When hanging artwork above the toilet, it is important to hang it at the right height. The toilet is shorter than 30 inches, so the artwork should be hung at a height of 58-62 inches from the center of the artwork to the floor. This will ensure that the artwork is visible and will not be hidden by the toilet.
If you’re installing a new toilet, or replacing an old one, it’s important to install the toilet flange at the correct height. The best practice is to install the flange on top of the finished floor, so that it’s flush with the floor. This will prevent leak paths from forming, because the flange will be at the correct height to accept the horn at the bottom of the toilet.
Where do I start rough in plumbing
This is just a brief note to say that waste lines are usually the first ones to be installed during plumbing for a new build. This is because the wastewater pipes are larger than the supply lines. The plumbers will then install the water supply piping after the waste lines have been put in place. For houses with slab foundations, the rough-in plumbing will be installed before the slab is poured.
The rough-in is when all of the mechanical, electrical, and plumbing lines are laid out in the home. Final connections are not made until later in the project. In order to begin the rough-in process, the basic framework of the home must be completed.
How much does it cost to install rough in?
The average cost to rough-in plumbing for a bathroom is $7,000. However, it can range from as low as $750 to as much as $20,000. The final price depends on the piping material, home size, labor fees, number of fixtures, and more.
There are two main types of flappers used in toilets: the two inch flapper and the three inch flapper. The size of the flapper you need depends on the size of the flush valve drain opening at the bottom of your tank. Most toilets will use the two inch flapper, but three inch flappers are becoming more popular in recent years. You can usually find three inch flappers in newer toilets manufactured since 2005.
Warp Up
There are a few different ways that you can measure the toilet rough in size.
One way is to measure from the center of the closet bolt to the finished wall. Most toilets have a measurement of 12 inches from the center of the bolt to the wall.
Another way is to measure from the back of the flange to the finished wall. Most toilets have a measurement of 10 inches from the back of the flange to the wall.
You can also measure from the center of the drain to the finished wall. Most toilets have a measurement of 9 inches from the center of the drain to the wall.
There are a few different ways that you can measure the rough in size for a toilet. One way is to take a measuring tape and measure from the back wall to the center of the drain. Another way is to measure from the center of the drain to the centerline of the toilet flange. The last way is to measure from the centerline of the toilet flange to the front edge of the toilet. Whichever way you choose, make sure that you measure the rough in size accurately so that your toilet will fit properly.