The Jones Stephens Toilet Flange is a flush valve and tank flange that mounts to the inside of the toilet bowl. It has an adjustable flange to fit 3″ or 4″ drain pipes and a 3″ or 4″ toilet tank bolt hole. The flange is made of solid brass with a chrome-plated finish.
A toilet flange is a pipe fitting that attaches a toilet to the floor. The flange is inserted into the floor and the toilet is then attached to the flange.
Table of Contents
How high should toilet flange sit above floor?
If you’re planning on changing your bathroom flooring, it’s important to keep the flange height in mind. The optimum height is 1/4 inch above the finished floor, which will allow for a good seal with almost any type of wax ring. If your flange is currently below this height, it’s likely that you won’t be able to achieve a good seal.
1. Remove the existing toilet
2. Remove the old wax ring
3. Block the waste hole
4. Plan your fit out with the old cut out
5. Test your new fit
6. Install the new offset toilet flange
Can toilet flange be lower than floor
If you install the toilet flange on top of the finished floor, you can avoid leak paths forming. This is because the flange will be at the correct height to accept the horn at the bottom of the toilet, and there will be no gaps for leaks to form.
Caulking around the base of the toilet will prevent bathroom liquids from getting underneath the toilet and creating a fouling area.
Does toilet flange sit on concrete or tile?
If your toilet flange is not on the same level as your finished floor, it could cause problems with your toilet. The toilet flange needs to be on top of the finished floor, meaning the bottom edge of the flange needs to be on the same plane as the toilet. So if your toilet sits on the tile, the flange needs to be on top of the tile too. The spacing of the toilet exit “horn” and sealing surface is designed for this height. If your flange is not level, it could cause problems with your toilet sealing properly, or could cause your toilet to rock and become unstable.
This is the distance that you will need to set the toilet flange from the back wall. You will want to make sure that the center of the flange is 12inches from the wall. This will ensure that the toilet is properly installed and will function correctly.
Why use an offset toilet flange?
An offset flange is a type of flange that is not centered on the waste pipe. This allows you to shift the location of the toilet by a couple of inches. PS Flanges with stainless steel rings cost a few bucks more than all-plastic versions.
You can’t put a new toilet flange over an old one. You have to remove the old one first.
Why you shouldn’t caulk around a toilet
Whether it be a wax gasket or a rubber gasket, caulking around the base of your toilet will help prevent leaks. Be sure to clean the surface around the base of the toilet and apply a continuous bead of caulking around the entire perimeter.
When installing a new toilet flange, it is important to slide the bolts into the new flange and secure them with washers and nuts. There is no need to use an adhesive when installing a gasket-sealed PVC flange.
What happens if you don’t caulk around toilet?
Caulk is used to prevent water from seeping under the toilet. If there is no caulk, any water that creeps underneath the toilet can remain undisturbed for some time. It will soon start to stagnate, providing a breeding ground for mold and fungus.
When you are installing a new floor, it is important to install the laminate flooring first so it is under the sink and toilet. This is because laminate flooring floats above the sub-floor on top of underlayment. With this in mind, the laminate flooring will expand and contract slightly with the temperature and humidity of the room. By doing this, you can avoid any damage that might be caused by the expansion and contraction.
Should toilet flange be screwed to concrete floor
The flange should be fastened to the floor before installation of the toilet. A dry fit should be done to make sure the toilet doesn’t rock. If it does rock, shims should be used to prevent rocking. Tightening the bolts alone probably won’t stop the rocking but could risk cracking the toilet or breaking the flange.
If you’re in the market for a new toilet flange, you’ll want to consider the options available to you. To help narrow down your choices, we’ve compiled a list of the seven best toilet flanges on the market today.
Secure Seal Technology: Danco 10672X
The Next Toilet Flange: Wax-Free
Coflex FlexOn Toilet Flange: Best For Plastic RV Toilets
Dometic Floor Flange: Best Longevity
Universal Drain 950P Toilet Flange: Best Long-Lasting
Danco Closet Flange: Best Semi-Flexible
Oatey Toilet Flange:Most Flexible
Can a toilet flange be too high?
If your toilet flange is too high, it may leak water and rock back and forth when used. This can warp or break the floor and also lead to the accumulation of mildew and mold.
If the old toilet is still there, measure from the center of the capped bolts (on the bottom) to the wall (not the baseboard). There should be 24 inches of clearance from the wall facing the bowl and 15 inches on each side as a guideline. If your measurements are between 115 and 125 inches, it is a 12-inch rough-in.
How much room do you need around a toilet flange
The reason for this minimum distance is to allow enough room for the waste pipe to connect to the flange. If the distance is too small, it will be difficult to make the proper connection.
If you’re unsure about which pipe to use for your plumbing project, be sure to check your local building codes. In general, ABS pipe is best for underground situations where it’s extremely cold, and PVC is ideal for indoor use where it’s not exposed to direct sunlight.
What happens if the toilet flange is not level
When you’re ready to install your space, take a good look at the flange to make sure the orientation arrows are where they need to be. If they’re not, your space will be installed incorrectly and could cause problems down the line. Once you’re satisfied that everything is in the right place, go ahead and install your space.
If you have a low toilet flange, it is important to make sure that your toilet is properly sealed to the waste pipe. Otherwise, you may face problems related to sewer gas odor or fluid leaks.
Final Words
The Jones Stephens toilet flange is a device that is used to connect a toilet to a drain pipe. It is made of a material that is resistant to corrosion and is designed to create a seal that is watertight.
This concludes our article on Jones Stephens toilet flanges. We hope you found it helpful in your search for the right product for your needs. Thank you for reading!