Are you tired of your old, dingy shower surround? If so, you may be considering a new shower surround. Lyons shower surrounds are a popular option among homeowners. They are available in a variety of colors and styles to match any bathroom décor. Lyons shower surrounds are made of durable materials that are easy to clean and maintain. Installation is easy and can be done in a few hours.
1. remove old shower surround
2. take measurements of shower area
3. purchase new shower surround
4. install new shower surround
Table of Contents
How to install Lyons linear bathtub?
When setting the bottom edge of the tub apron on the floor, be careful to rest it against the front edge. This will help to ensure a more secure and level installation.
When installing cement board or an equivalent moisture-resistant backing material on walls behind tub and shower enclosures composed of tile or panel assemblies with caulked joints, make sure not to use paper-faced drywall. This will help to prevent any moisture damage that could occur over time.
How do you attach a shower surround to the wall
When aligning the front edges of two surfaces, it is important to ensure that there is no more than a 1/32 inch gap between them. This can be done by starting at the bottom and working your way up.
If you’re looking to update your bathroom with a new bathtub surround, you can do it yourself with some careful measuring and sealing. Make sure to measure your cardboard or paper template carefully, and seal and caulk any fixture openings well to keep them waterproof. With some careful planning, you can update your bathroom in no time.
How to install Lyons linear shower walls?
Check for a tight fit in each corner Using shims if needed check that each panel rests flat against the wall and that the joints are flush
An acrylic or fiberglass surround kit is a popular option for alcove enclosures for bathtubs and showers. This type of kit is cheaper and easier to install than ceramic tile wall enclosures and is remarkably easy to maintain.
Does drywall go behind a shower surround?
It’s not a good idea to install shower surrounds and bathtub walls over drywall because drywall is not a material that’s intended to get wet. Drywall absorbs moisture, which can cause it to lose its structural integrity. This can lead to serious problems down the line, so it’s best to avoid it if possible.
Drywall is not recommended for use in bathrooms because it is absorbent and will lose structural integrity over time. If you are converting a room that was never a bathroom into a wet space, it is best to use materials that are designed for moist environments.
Why do you not seal the inside of a shower enclosure
When sealing shower enclosures with silicone, be sure to only apply it to the outside. If silicone is applied to the inside as well, water may leak through the profiles and reach the outside. However, if both the inside and outside are sealed, water may stagnate inside the profiles.
Loctite Power Grab Tub Surround Interior Construction Adhesive is an ideal product to use for bonding most bathroom and shower enclosures. It is unaffected by moisture, steam, water, heat or cold when fully cured, making it a great choice for many different applications.
What adhesive do you use for shower walls?
If you are looking for a construction adhesive that can bond most bathroom and shower enclosures, Loctite Power Grab Tub Surround Interior Construction Adhesive is a good option. This construction adhesive has 0 second instant grab and dries faster than previous Power Grab formulas. It is unaffected by moisture, steam, water, heat or cold when fully cured.
Loctite PL 550 Tub Surround Adhesive is an excellent choice for bonding most bathroom and shower enclosures, as it will not harm or burn the tub kit materials. This water-based adhesive is perfect for this task, as it resists moisture, steam, water, heat, and cold when fully cured.
Do you need vapor barrier behind shower surround
It is important to have a moisture barrier beneath your shower pan and behind your shower walls in order to prevent moisture damage. Moisture barriers can be made of polyethylene or a membrane that is rolled directly onto the drywall. No matter what they are made of, without them, your shower is subject to moisture damage.
While surrounds are typically less expensive than tile, some high-end materials can be more costly. For example, granite may be more expensive than tiling with some grades of tile. When deciding between the two, it’s important to consider your budget and the look you’re hoping to achieve.
Do I need cement board for shower walls?
Whenever you install tile in any area of your house, you need a special substrate or base layer. In showers, the standard substrate is a tile backer like cement board or some type of sheet or liquid membrane that protects the shower stall’s underlying structure from water.
When you are planning to install a new shower, you have two main choices for the drain location. You can install the drain against the wall, or you can place the drain free-in-the-floor. We recommend installing the drain against the wall, for a few reasons.
First, installing the drain against the wall offers a one-sided slope, which is easier to work with and requires less tile cutting. Second, this option usually provides a better drain flow, since the water can run straight down the drain pipe without having to make any turns. And finally, an against-the-wall drain installation just looks nicer, in our opinion!
Conclusion
1. Before you begin, familiarize yourself with the parts and hardware.
2. Cut two pieces of lumber to the correct height for the shower surround using a miter saw. These will serve as the side supports for the surround.
3. In order to create a watertight seal, apply a liberal amount of caulk to the back wall where the shower surround will be installed.
4. Use L-brackets to secure the side supports to the back wall. Make sure that the L-brackets are positioned so that they will not be visible once the surround is installed.
5. Place the shower surround on top of the side supports and secure it in place using screws.
6. Apply a bead of caulk around the perimeter of the shower surround.
7. Install the showerhead, faucet, and any other fixtures according to the manufacturer’s instructions.
8. Test the shower surround for leaks by running the shower for a few minutes.
Installing a Lyons shower surround is a simple and easy process that anyone can do. The results are a beautiful and durable shower surround that will last for years.